Rosewill WIRELESS N ADAPTER RNX-N150UBE Guía de usuario Pagina 27
- Pagina / 83
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
OPENING ADMIN
groov Box User’s Guide
20
Turning On the groov Box
1. Check to make sure that the groov Box is plugged in and receiving power.
2. Firmly press the On/Off button until the SYS LED lights up (in about one second), then release.
Take a look at the LNK ACT light for ETH0; if the cable is properly connected, the LNK ACT light
should be on or blinking.
NOTE: Always wait until the SYS LED has stopped blinking before you try to log into groov. Otherwise,
you may not be able to use the hostname to log in. If this happens, see page 65.
CAUTION: If you press the button for longer than eight seconds, the groov Box will be reset to default
settings. Your project and all passwords will be erased.
Turning Off the groov Box
With the groov Box on, press the On/Off button. The SYS LED will blink blue and then turn off.
Always allow the groov Box to turn off properly before removing power.
Resetting groov Box to the Factory State
Resetting the groov Box resets the default network settings and erases all user data, including your
project. groov will be in the state it was when shipped from the factory, so any upgrade to groov
Admin, groov App, or license(s) will have to be re-applied.
CAUTION: When the groov Box is reset to factory default settings, your project and all passwords will be
erased.
1. Check to make sure that the groov Box is turned off, but the device is plugged in and receiving
power.
2. Press and hold the On/Off button for at least eight seconds and until the SYS LED is blinking red
and green. Then release the button.
The reset defaults operation can last several minutes. When the process is complete, the groov
Box will power off.
NOTE: Do not remove power from the groov Box or turn it off while the SYS LED is blinking red and
green. If you do, you'll need to repeat the reset defaults operation from step 1.
3. Firmly press and release the On/Off button to turn on the groov Box.
NOTE: Always wait until the SYS LED has stopped blinking before you try to log into groov. Otherwise,
you may not be able to use the hostname to log in. If this happens, see page 65.
Opening Admin
Using groov Admin you can back up and restore your projects and project settings, update firmware,
set up wired and wireless networking, and more.
- GROOV BOX 1
- USER’S GUIDE 1
- FOR GROOV-AR1 1
- GROOV BOX USER’S GUIDE 2
- Table of Contents 4
- 1: Welcome 8
- Choose Your groov 9
- About this Guide 10
- Other groov Resources 10
- System Requirements 10
- A Note on Browsers 11
- System Architecture 12
- What’s In This Guide 13
- Product Support 14
- PRODUCT SUPPORT 15
- 2: Getting Started 16
- Step 2. Choose a Location 18
- Step 3. Mount the groov Box 18
- DIN rail clip 19
- ETH0 to computer network 19
- ETH1 to control network 19
- (if on a separate subnet) 19
- Step 6. Turn on the groov Box 21
- Step 8. Open groov 22
- Serial number 24
- 3: Powering On, Logging In 26
- Opening Admin 27
- 1. Open groov Find 28
- 2. Click Yes 28
- Logging into Admin 30
- For Chrome 31
- For Firefox 31
- For Safari 32
- For Internet Explorer 32
- 4: Using groov Admin 34
- Using Admin’s Quick Start 35
- Assigning a Static IP Address 36
- 4. Click Save 37
- 3. Click Save 38
- 2. Click ETH1 39
- 2. Click WLAN0 40
- 6. Enter the Network Key 40
- Make sure that WLAN0 is 42
- Disabled 42
- Backing Up groov 44
- 4. Do one of the following: 45
- 5. Click Backup 45
- Restoring groov 46
- Updating groov Admin 47
- Restarting the groov Box 48
- Checking System Information 50
- Checking Hardware Status 51
- Setting the System Time 52
- Changing the Time Zone 53
- Time Server 53
- 5. Click Sync and Apply 54
- SETTING THE SYSTEM TIME 55
- 5: Using an SSL Certificate 56
- 4. Click Create Now 58
- Store on a Computer 61
- Windows 7 Windows 8 62
- Expand this 63
- Click here 63
- Step 1: Create a CSR 65
- Basic Troubleshooting 70
- Troubleshooting Q&A 71
- A: Specifications and 74
- Dimensions 74
- B: Connectors and LEDs 76
- SYS LED On/Off button 77
- Ethernet LEDs 77
- C: Replacing the Battery 78
- WiFi Adapter 80
Relacionado con productos y manuales para Redes Rosewill WIRELESS N ADAPTER RNX-N150UBE
Redes Rosewill RNX-N1/N1MAC Manual de usuario
(71 paginas)
(71 paginas)
Redes Rosewill RNX-N180PCE Guía de instalación
(11 paginas)
(11 paginas)
Redes Rosewill RNX-N250PC Guía de instalación
(14 paginas)
(14 paginas)
Redes Rosewill RNX-N1/N1MAC Manual de usuario
(53 paginas)
(53 paginas)
Redes Rosewill RNX-N4 Manual de usuario
(94 paginas)
(94 paginas)
Redes Rosewill RNX-EasyN400 Manual de usuario
(112 paginas)
(112 paginas)
Redes Rosewill RNX-N180PCE Manual de usuario
(40 paginas)
(40 paginas)
Redes Rosewill RNX-N150RT Manual de usuario
(8 paginas)
(8 paginas)
Redes Rosewill RNWD?N9003PCE Manual de usuario
(46 paginas)
(46 paginas)
Redes Rosewill RNX-G400 Manual de usuario
(13 paginas)
(13 paginas)
Redes Rosewill RNX-N4PS Manual de usuario
(2 paginas)
(2 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales